Vermont Castings DV360 Operations Instructions download pdf (Page 8)

DV360/580 Series Direct Vent Gas Fireplace

20010667

Gas Speciﬁcations

MAX. MIN.

GAS INPUT INPUT

MODEL FUEL CONTROL B.T.U.H B.T.U.H.

DV360RN Natural Gas Millivolt Hi/Lo 30,000 18,500

DV360RP Propane Millivolt Hi/Lo 30,000 17,000

DV360EN Natural Gas 24 Volt Hi/Lo 30,000 18,500

DV360EP Propane 24 Volt Hi/Lo 30,000 20,000

DV360RFN Natural Gas Comfort Control 30,000 20,000

DV360RFP Propane Comfort Control 30,000 21,000

DV580RN Natural Gas Millivolt Hi/Lo 38,000 26,500

DV580RP Propane Millivolt Hi/Lo 38,000 27,000

DV580EN Natural Gas 24 Volt Hi/Lo 38,000 26,500

DV580EP Propane 24 Volt Hi/Lo 38,000 27,000

DV580RFN Natural Gas Comfort Control 38,000 26,500

DV580RFP Propane Comfort Control 38,000 27,000

Gas Inlet and Manifold Pressures

Natural LP (Propane)

Minimum Inlet Pressure 5.5” w.c. 11.0” w.c.

Maximum Inlet Pressure 14.0” w.c. 14.0” w.c.

Manifold Pressure 3.5” w.c. 10.0” w.c.

High Elevations

Input ratings are shown in BTU per hour and are

certiﬁed without deration for elevations up to

4,500 feet (1,370m) above sea level.

For elevations above 4,500 feet (1,370m) in USA,

installations must be in accordance with the

current ANSI Z223.1/NFPA 54 and/or local codes

having jurisdiction.

In Canada, please consult provincial and/or local

authorities having jurisdiction for installations at

elevations above 4,500 feet (1,370m).

Gas Line Installation

When purging gas line the front glass

must be removed.

The gas pipeline can be brought in through the right

side of the appliance. Knockouts are provided at conve-

nient locations to allow for the gas pipe installation and

testing of any gas connection.

The gas line connection can be made with properly

tinned 3/8” copper tubing, 1/2” rigid pipe or an approved

ﬂex connector. Since some municipalities have addi-

tional local codes, it is always best to consult your local

authority and the CSA-B149.1 installation codes.

For USA installations consult the current National Fuel

Gas Code, ANSI Z223.1/NFPA 54.

FP297A

INSTA VENT FREE

UVHB26 GAS SUPPLY

7/1/98

1/2” Gas Supply

1/2” NPT x 3/8” Flare Shut-

off Valve

3/8” Flex Line

(from valve)

FP297a

Fig. 6 Typical gas supply installation.

Always check for gas leaks with a mild

soap and water solution applied with a

brush no larger than 1” (25 mm). Never

apply soap and water solution with a spray

bottle. Do not use an open ﬂame for leak

testing.

The ﬁreplace valve must not be subjected

to any test pressures exceeding 1/2 psi.

Isolate or disconnect this or any other gas

appliance control from the gas line when

pressure testing.

The gas control is equipped with a captured screw type

pressure test point, therefore it is not necessary to pro-

vide a 1/8” test point up stream of the control.

When using copper or ﬂex connector use only approved

ﬁttings. Always provide a union when using black iron

pipe so that the gas line can be easily disconnected for

burner or fan servicing. (Fig. 6) See the gas speciﬁca-

tions for pressure details and ratings.

Remote ON/OFF Switch Installation

Do not wire the remote ON/OFF wall switch for this gas

appliance into a 120v power supply.

1. Thread wire through the electrical knockout located

on either side of the unit. Take care not to cut the

wire or insulation on metal edges. Ensure the wire is

secured and protected from possible damage. Run

one end of the gas control valve and the other end to

the conveniently located wall switch.

2. Attach the wire to the ON/OFF switch and install

switch into receptacle box. Attach cover plate to

switch.

3. Connect wiring to gas valve. (Fig. 7)

TPTH

FP1218

Remote switch

wiring

8/02

Remote ON/OFF

Switch

FP1218

Fig. 7 Remote switch wiring diagram for R models.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 55 56

Comments to this Manuals

No comments

Vermont Castings DV360 Operations Instructions Page 8

Comments to this Manuals

Related products and manuals for Fireplaces Vermont Castings DV360