Vermont Castings Stardance SDV30 Operations Instructions download pdf (Page 19)

Stardance Direct Vent/Natural Vent Gas Heater

20007065

Install the Vent Pipe

Apply a bead of sealant around bottom end of inner

starter pipe (found in bag with logset) and attach to

stove. Apply a bead of sealant around top of inner

starter pipe and install the Z31D00 FSDHAG Draft

Hood according to Draft Hood instructions. (Fig. 33)

Attach the ﬁrst section of venting to the draft hood. De

pending on the length of the individual venting sections

and the lengths of the decorative pipe (if installed), you

may need to slip the decorative pipe over the venting

sections before attaching upper sections to lower ones.

The sections of decorative pipe should be oriented with

their seams (if any) toward the wall; sections usually

do not need to be fastened at each joint, other than

slip sections. If the layout includes a slip section, this

should be the last section of pipe visible in the room, at

the ceiling. Complete the venting according to the vent

maker’s instructions.

Install the Log Set

1. Remove the logs from their packaging, and inspect

each piece for damage. DO NOT INSTALL DAM-

AGED LOGS.

2. Install the rear log centering it side to side on the

sheet metal shelf at the back of the ﬁrebox. (Fig. 34)

The log will touch both sides and the back wall of the

ﬁrebox.

3. Install the right log by engaging hole on bottom with

pin on the rear log. (Fig. 34) Then set right bottom

side on the burner so the edge of the log touches the

right side of the ﬁrebox. The right log does not use

the locator pins on the burner to stay in place.

LG141

Stardance

Install logs 1

12/11/00 djt

Left Log

Right

Log

Decorative Grate

Rear Log

LG141

Fig. 34 Install the back, left and right logs.

4. Install the left log by engaging hole on bottom with

pin on rear log. (Fig. 34) Then set left bottom side

on the burner so the edge of the log touches the left

side of the ﬁrebox.

5. Loosely sprinkle the lava rocks directly on top of the

burner in front of and between the decorative grate

and the right and left logs. Use the lava rock to cover

brackets on the burner. (Fig. 35)

LG142

Stardance

Install logs 2

12/1

1/00 djt

Lava Rock

LG142

Fig. 35 Completed log installation.

Connect the Gas Supply Line

Check the Rating Plate attached by a steel cable to the

ﬁrebox, to conﬁrm that you have the appropriate ﬁrebox

for the type of fuel to be used. The Stardance may be

converted from one gas to another using the appropri-

ate Fuel Conversion Kit listed on Page 39.

CAUTION

This appliance should only be connected

by a qualiﬁed gas technician. Test to

conﬁrm manifold pressures as speciﬁed

below.

The Stardance Heater and its individual shutoff

valve must be disconnected from the gas supply

piping during any pressure testing of that system

at test pressures in excess of 1/2 psig (3.5 kPa).

The Stardance Heater must be isolated from the

gas supply piping system by closing its indi-

vidual manual shutoff valve during any pressure

testing of the gas supply piping system at test

pressure equal to or less than 1/2 psig.

There must be a gas shutoff between the stove

and the supply.

In order to connect Natural Gas, use a ﬁtting with

3/8” NPT nipple on the valve side and 1/2” natural

gas supply line with an input of 28,000 BTUs at a

manifold pressure of 3.5” and minimum inlet sup-

ply for adjustment of 5.5” w.c.

In order to connect Propane, use a ﬁtting with

3/8” NPT nipple on the valve side and 1/2” pro-

pane gas supply line with an input of 28,000 BTUs

at a manifold pressure of 10.0” and minimum inlet

supply for adjustment of 11.0” w.c.

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 43 44

Comments to this Manuals

No comments

Vermont Castings Stardance SDV30 Operations Instructions Page 19

Comments to this Manuals

Related products and manuals for Fireplaces Vermont Castings Stardance SDV30